Can you replace zipper pull

However, as long as you choose the same size and type slider, the locking vs. So even if your original slider was locking, you can replace it with a non-locking slider as long as the other aspects of the slider match the original. These black, non-locking pull sliders are specially designed to resist corrosion and UV rays. On a standard coil zipper, the zipper pull tab would be on the toothed side. Ready to shop for a zipper slider?

At Sailrite, you will find 4. We also offer a variety of metal zipper sliders and chains. Be the first to Write a Review. Javascript is disabled on your browser. To view this site, you must enable JavaScript or upgrade to a JavaScript-capable browser. You may remove the old zipper pull tab if needed - Sometimes the zipper pull tab breaks in half or the top part of the slider comes off.

If the top part of the slider comes off there is nothing to hold the pull tab in place. In that case, lift it off the zipper. You can wriggle your old pull tab out of your slider has a hook-type loop instead.

Grab a pair of pliers to pull off any broken bits of zipper pull tabs. Insert the replacement pull tab - You will notice 2 small stubs when you remove the loop of the zipper slider. These stubs are where the loop is attached to the slider. Place your replacement pull tab such that one of the stubs is inside the loop at the top of the pull tab. For hook-type loops, slide the replacement pull tab under the slit.

You may use a flat-head screwdriver if the slit is too small. Snap it shut after you have replaced the loop - Put the loop back on top of the zipper slider ensuring that the teeth fit into the grooves. Press down on it firmly. For a hook-type loop, your job is done. However, if you feel that the pull tab may fall off, just use pliers to clamp the loop shut. Inserting a replacement zipper pull is quite simple. Lift the zipper slider that holds the pull tab in place. Be careful not to damage the slider or the piece that holds the tab in place.

If you apply too much force it may break off entirely. Work slowly and with care to avoid this mishap. Use pliers to remove any remaining pieces of the old pull tab, if necessary.

Now slide the new zipper pull in to place underneath the lifted piece of metal. Secure it so that it does not slide out. Bend the slider that secures the pull tab back into position. Once again, be careful so that you don't accidentally break the slider. Yes, you can buy quite a variety of zipper pulls from Michaels.

They also sell zipper repair kits. Yes, Walmart sells zipper pulls. They are available in packages of multiple zipper pulls. Several things can be used as a zipper pull tab. You can use whatever is handy at the moment as a temporary solution. A keyring, a sturdy piece of yarn, a rubber band, a thin piece of wire- all of these things can double up as a zipper pull in emergency times.

You can also use a piece of fabric sewed up like a zipper pull. Move the locking mechanism out of the way, if needed.

Some types of zippers have a locking mechanism. You can see this mechanism if you look closely at the zipper from the side, then move it up and down. You'll notice a lock moving up and down inside the loop that the zipper pull was attached to. If you can see the lock inside the loop, then move the zipper slider slowly until the loop is clear.

Slip a paper clip through the loop for a temporary option. Find the end on the outside of your paper clip. Feed it through the loop on your zipper. Rotate the paper clip so that both of the U-shaped loops are facing away from the zipper. You can also use a colored paper clip if you want the pull tab to match the zipper slider.

Thread a key ring onto the zipper slider for a sturdier option. Find a small key ring that is less than 1 inch 2. Pry open the end with your fingernail, a flat-head screwdriver, or a knife. Slide the end of the key ring into the loop. Feed the key ring through the loop until it is completely attached and closes by itself.

Zipper up your jeans, slide the key ring over the button, then close the button. Avoid using key rings that are too large, or they will look clunky. Use a thin cord if you need something quick and easy. Find some cord that is thick enough to fit through the loop on your zipper pull. Cut a short piece, then feed it through the loop. Cut the rest of the string off.

Match the color of the cording to the zipper, if possible. Use a thin ribbon if you want a nicer touch. Choose satin or grosgrain ribbon thin enough to fit through the loop on your zipper pull. Cut it down to 2 to 3 inches 5. Match up the ends of the ribbon to make sure that it is centered, then finish it in 1 of the following ways: [14] X Research source Tie the ends together in an overhand knot to make a loop.

Sew across the ends 2 to 3 times using a zigzag stitch to create a loop. Use hot glue or fabric glue to glue both ribbon halves together to form a single strip. Twist a wire through the loop for something more like a pull tab. Cut a short piece of wire. Slip it through the loop on the zipper, then twist the ends together to form a stem. Leave some space between the twisted part and the loop so that you can move the pull tab up and down. If you want the pull tab to match the zipper slider, use a colored paper clip instead.

Use heavy-duty jump rings to attach charms if you want a fancy pull tab. Use a pair of pliers to open a heavy-duty jump ring. Time Required. Patagonia and iFixit are celebrating the stories we wear by collaborating to provide guides for Patagonia's most popular apparel repairs.

Just replace the zipper slider and the stop that keeps it from sliding off. Determine the size of your replacement slider by looking on the bottom of your existing slider. For replacement parts or further assistance, contact Patagonia Customer Service.

You may need to tug a little to get the slider over the webbing from the old stop. Make sure the zipper slider is oriented right-side up when you slide it back onto the zipper. Position the new stop over the webbing in the same place where the old stop was located. Cancel: I did not complete this guide.

Badges: Amazon has replacement parts, but I found you can get almost any zipper parts from a sailing supply company called sailrite.